Where Runoff Concentrates on New York Farm Fields

Find the draws and swales where water from the ground above comes together, from public lidar, and take the map to your Soil and Water Conservation District or NRCS field office.

Rain and snowmelt that run off a field do not leave it evenly. Water runs downhill and gathers in the low lines of the ground: a swale across a hay field, a draw at the bottom of a pasture, the corner where a farm lane meets the hedgerow. NRCS calls that concentrated surface flow, and it is the condition one of its conservation practice standards is written for.

The USDA Natural Resources Conservation Service (NRCS) publishes conservation practice standards. Its Grassed Waterway standard (Code 412) defines the practice as “a shaped or graded channel that is established with suitable vegetation to convey surface water at a nonerosive velocity using a broad and shallow cross section to a stable outlet,” and says it is applied “in areas where added water conveyance capacity and vegetative protection are needed to prevent erosion and improve runoff water quality resulting from concentrated surface flow.” Among its listed purposes: “Prevent gully formation.”

NRCS’s overview of the practice adds that waterways “are constructed to convey runoff from concentrated-flow areas, terraces, or diversions where erosion control is needed,” and ends: “For further information, contact your local NRCS field office.”

So the first question on the ground is a terrain question: where does the water come together? That part you can map from your desk.

Map it in seven steps

  1. Select the field. Open Property and click the field to use the tax parcel as the working area, or take up to 25 parcels at once for a whole farm. Where the public parcel service has no parcel, or you want one field only, draw a box or polygon instead. Open it on the map · How it works
  2. Map the flow paths. Run Water & Drainage. Thicker, paler lines drain more land, and tapping any line shows the acres upstream of it. A field where several faint paths join into one strong one is a field where runoff concentrates; the joins and the draw below them are the places to look at first. The terrain loaded reaches beyond your boundary, so water arriving from a neighbor’s ground or the road is counted. Open it on the map · How it works
  3. Check where water sits. Switch to the Ponding view to see the hollows that would hold water once full, with their depth, area and volume. Real hollows drain into the soil and evaporate, so these are upper bounds. A long strip of ponding along a farm road usually means a culvert the lidar cannot see. Open it on the map · How it works
  4. Follow water from one spot. Open Downhill Path and click a spot, such as a barnyard, a feeding area or the top of a draw. The line shows where rain from there runs, and the panel says how far it goes before it joins a water path, becomes a watercourse or reaches a stream. Open it on the map · How it works
  5. See the land draining to a point. Open Catchment and click the bottom of a draw or the corner where water leaves the field. The blue area is all the land that drains there, in acres. If much of it lies outside your boundary, the water in that draw is partly someone else’s runoff, which is worth knowing before you talk to a planner. Open it on the map · How it works
  6. Read slope and wet ground alongside. Slope & Aspect shows how steep the ground above each draw is, and Wetness Map ranks the field from dry ground to the flats and hollows where the shape of the land concentrates water. Neither is a soil or wetland map; they are the terrain half of the picture. Open it on the map · How it works
  7. Look back through old photos. Aerial History steps through every year of aerial photos NYS ITS Geospatial Services holds for a spot, 2000 to 2025. Swipe between them to look for old roads, filled ditches or a stream that has moved. Open it on the map · How it works

Map the flow paths on your field

Select the parcel or draw a box, and run Water & Drainage. Free to use, no account.

Open Water & Drainage →

What the map can and can’t tell you

The flow paths are traced from the USGS 3DEP bare-earth lidar model: each cell passes its water to its steepest neighbor and the land upstream of every cell is added up. That is a good picture of where the surface sends water. It is not the whole picture:

  • No soil, erosion or nutrients. The tools do not model what runoff carries. EPA notes that producers “can adopt soil and water conservation practices to reduce the runoff of sediment, nutrients, bacteria, pesticides, and other pollutants from their operations,” and that the effects of runoff “vary widely, depending on the type of operation, landscape conditions, soils, climate, and farm management practices.” The terrain is one of those; the rest is on the ground. For soils, NRCS’s Web Soil Survey provides soil data and information.
  • No drains or culverts. Tile drains, culverts and ditches narrower than the sampling are not in the lidar. Draw the ones you know under Culverts & barriers.
  • The ground on the day it was flown. Leveling, ditching and new tile lines put in since the lidar survey do not show. Data Here lists which surveys cover a spot and when they were flown.
  • No design. Nothing here lays out or engineers a practice. The 412 standard itself says to plan, design and construct grassed waterways “to comply with all Federal, State, and local laws and regulations.” NRCS’s Grassed Waterway page notes that national conservation practice standards should not be used to plan, design or install a conservation practice, and points to the Field Office Technical Guide for the documents at the local level.

Who to take the map to

  • Your county Soil and Water Conservation District. The New York State Department of Agriculture and Markets says New York’s 58 county Soil and Water Conservation Districts “provide programs and services to conserve, enhance, and protect soil and water resources across the state.” Find yours in the department’s list of district offices.
  • Agricultural Environmental Management (AEM). The department describes AEM as “a voluntary, incentive-based program available to all farmers through their local Soil and Water Conservation District.” It runs in tiers, from an inventory of the farm to, at Tier 3, conservation plans “addressing concerns and opportunities tailored to farm goals,” and then putting them in place. Funding for that work includes the Agricultural Nonpoint Source Abatement and Control program, which the department calls “a cost-share grant program that provides funding to address and prevent potential water quality issues that stem from farming activities,” with funds applied for and awarded through the county districts.
  • Your NRCS field office. NRCS’s conservation technical assistance helps producers identify conservation objectives and a roadmap for conservation on their operation. Start from NRCS’s New York state office page, or find your local USDA Service Center with the farmers.gov service center locator.

What to bring: the flow path map with the acres on the main draws, the catchment of each draw you are asking about, and the slope map. The property report’s data ZIP can hold a slope map, the flow paths, a wetness map, contours and an aerial photo for the area in one download. Parcel boundaries are not put in New York files, so the parcel itself stays on the map.

Related guides

Frequently asked questions

How do I find where runoff concentrates in my field?

Select the field on the map, as a tax parcel or a box you draw, and run Water & Drainage. Each flow path is labeled with the acres of land draining through it, so the draws where paths join and the figure climbs are where water from the ground above comes together. Walk those spots, ideally after a storm, to see what the water actually does there.

Can this tell me where to put a grassed waterway?

It shows where concentrated flow is, which is where NRCS’s Grassed Waterway standard (Code 412) says the practice applies. Whether a waterway or another practice fits, and how it is laid out and built, is a question for your Soil and Water Conservation District or NRCS field office: NRCS notes that its national practice standards should not be used to plan, design or install a practice, and points to the Field Office Technical Guide for the local version. The maps help that conversation; they do not replace it.

Does the map know about my tile drains, culverts and ditches?

Not unless you draw them. Water is routed over the surface of the lidar ground model, so a culvert under a farm road or a narrow ditch is invisible to it. Draw them under Culverts & barriers in Water & Drainage and run again; the result says when your lines were used.

Does it show erosion or nutrient loss?

No. It shows where the ground sends water and where water would sit. It does not model erosion, sediment, nutrients or soil. For soils, NRCS’s Web Soil Survey provides soil data and information; for what runoff carries from a particular field, ask your Soil and Water Conservation District.

Who helps New York farms with water quality?

Your county Soil and Water Conservation District. The New York State Department of Agriculture and Markets describes Agricultural Environmental Management (AEM) as a voluntary, incentive-based program available to all farmers through their local district, and its Agricultural Nonpoint Source Abatement and Control program as a cost-share grant program for water quality projects on farms, applied for through the county districts. This site does not interpret any program’s requirements.

Is it free?

Running every tool on the map is free, with no account. Downloading the flow paths, catchment outlines and grids as files needs a pass.

Sources

About the data

Ground elevations come from the public-domain USGS 3DEP seamless bare-earth model, above NAVD 88. Source detail varies by location. Lidar coverage and source resolution vary across New York. Check your location against the USGS 3DEP index; no statewide coverage percentage is asserted. Buildings and trees are excluded from every terrain analysis in this edition. More from the USGS 3D Elevation Program.